How do I dry my cast after a shower?

How Should We Care for the Cast?

1. Flush the cast and liner with clean water to remove soap after showers.
2. Dry the waterproof cast with a hair dryer on the cool setting after showering or swimming.

Can you shower with a cast on your foot?

You should use some form of water protection for your cast every single time you shower or bathe. If your cast happens to get wet, you’ll want to pay a visit to your doctor to check it and see if it needs to be replaced.

What happens if a cast gets wet inside?

DON’T get non-waterproof casts wet. If conventional padding inside a cast gets wet, it won’t dry. Neither will the skin next to it. That can cause significant problems, including skin infection, skin death and permanent scarring, Dr. Goodwin says.

Can you take a shower with fiberglass cast?

A new waterproof cast lining was developed in the 1990s for both plaster and fiberglass casts. This new lining combined with a fiberglass cast means a completely waterproof cast. That makes it possible for you to bathe, shower, and swim while wearing a cast.

How do you dry a cast fast?

Loosely wrap an ice pack covered in a thin towel around your child’s cast at the level of the injury. Wrapping the ice is important to keep the cast dry. Ice that’s packed in a rigid container and touches the cast at only one point won’t be as effective.

How do you waterproof a shower cast?

Sealable plastic bags can be fit over a cast to keep it safe from water.

1. Newspaper bags, bread bags, or small trash bags usually work well. You would pull a bag over the cast and seal it on top using a rubber band or duct tape.
2. Make sure to check the bag for any holes prior to using it to waterproof your cast.

How do you keep a cast dry?

Keep your child’s cast dry during baths or showers by covering it with two layers of plastic, sealed with a rubber band or duct tape. Avoid swimming while wearing a cast that isn’t waterproof. A fiberglass cast that has a waterproof liner can get wet.

What happens if you shower with a cast?

You may have to keep the broken limb outside of the shower during the bathing process. However, even if you keep your cast away from the water, do not bathe or shower without a cover. Even a small amount of water can be harmful to a cast.

How do you keep a cast from getting wet?

How do you dry a wet fiberglass cast?

In general, casts are meant to stay dry. A wet cast can lead to skin irritation or infection. Plaster casts and fiberglass casts with conventional padding aren’t waterproof. Keep your child’s cast dry during baths or showers by covering it with two layers of plastic, sealed with a rubber band or duct tape.

How do you waterproof a cast?

3 Simple DIY Solutions for How to Waterproof a Cast

1. Purchase a Cast Cover. Cast covers fit over the cast and fasten with a watertight seal.
2. Use Plastic Bag & Tape. Plastic bags and tape are not as handy as a cast cover, but will work to keep your cast dry, for the most part.
3. Cover with Plastic Wrap.

How do you Keep Your Feet from getting wet in the shower?

Another plastic bag around foot that is rubber banded above towel. (Towel is to catch any drips that get through the seal of the outer plastic bag). Get a sturdy plastic stool or chair and sit on it in the shower, with legs up and pointed outside of water zone, also plastic bagged to block any spray.

How do I keep my cast dry?

Here, some ideas for keeping your cast dry so you can and still keep yourself clean. One tip not to try is to shower by holding the cast out of the way. Water will inevitably drip down your arm or leg, soaking the cast’s padding. Even if you plan on holding your cast out of the path of the water, find something to cover it.

Can you shower with a cast on?

One tip not to try is to shower by holding the cast out of the way. Water will inevitably drip down your arm or leg, soaking the cast’s padding. Even if you plan on holding your cast out of the path of the water, find something to cover it.

How do you stop a cast from leaking water?

This method may leave gaps where water can seep through, but it is an inexpensive and easy method to cover the cast. Using a rubber band at the top of the cast can help ensure the seal will not leak. Again, refrain from submerging the cast in water, as the seal may not be as tight as you hope.